Eurotherm 3116 PID User's Guide Page 49
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3100/3200 Series
Part No HA028651 Issue 3.0 Mar-06 47
9.1.9 AA Relay (AA) (Output 4)
This is a changeover relay and is optionally available in 3200 controllers. It is available as standard in 3116 controllers.
Connections are made to terminals AA, AB, and AC. The way in which this relay operates is determined by parameters in the AA
List. OP4 beacon is operated from the AA relay output channel.
AA RELAY ‘aa’
Name Scrolling
Display
Parameter Description Value Default Access Level
4. TY P E
OUTPUT 4
TYPE
Output channel 4 hardware
type
reLy
Relay output
reLy
Read only
none
Disabled
d.OUt
Conf
d.OUt
Digital output
UP
Valve open codes VC and VP only
dwn
Valve close codes VC and VP only
Heat
Heat output
4.FUNC
FUNCTION Output channel 4 function
If the instrument is ordered
as valve positioner (codes VC
or VP), only options available
are , none, d.out, UP, or
dwn
Note: If output 4 is set to
up ensure the other valve
position output is set to
dwn and vice versa
CooL
Cool output
none
No event connected to the output
4.SRC.A
I/O 4 SOURCE
A
AL1
Alarm 1 *
AL2
Alarm 2 *
4.SRC.B
I/O 4 SOURCE
B
AL3
Alarm 3 *
AL4
Alarm4 *
4.SRC.C
I/O 4 SOURCE
C
ALL.A
All alarms
nw.AL
Any new alarm
Ct.AL
CT alarm, load, leak & overcurrent
Lbr
Loop break alarm
Sbr
Sensor break alarm
t.End
Timer end status
t.run
Timer run status
mAn
Manual status
rmt.F
Remote fail - see section 9.1.2.
Pwr.f
Power fail
4.SRC.D
I/O 4 SOURCE
D
These parameters only
appear when the channel
function is a Digital OP,
i.e. 4.FUNC = d.Out
Selects an event status to be
connected to the output
channel.
The output status is the
result of an OR of Src A, Src
B, Src C, and Src D
Up to four events can,
therefore, operate the
output
See section 9.1.4.
prg.e
Programmer event. See also section
13.2.3.
none
Conf
4. P LS
OUTPUT
MINIMUM
PULSE TIME
Minimum output on/off
time.
Only applies to time
proportioning outputs and
prevents relays from
switching too rapidly
0.0 to
150.0
0 to 150 seconds 5.0 sec Conf
nor
Normal
4.SENS
SENSE To configure the polarity of
output channel 4
See also section 9.1.3..
Inv
Inverted
nor
Conf
* The mnemonic for the alarm will change depending upon the alarm configuration.
- 3100/3200 1
- 1.3 Dimensions 8
- 1.4 Step 1: Installation 9
- 1.5 Order Code 10
- 2. Step 2: Wiring 11
- 2.5 Wire Sizes 13
- 2.6 Precautions 13
- 2.13 Current Transformer 15
- Local ground 16
- Diagram 17
- ☺ Helpful hints 18
- Pollution Degree 2 19
- 4. Switch On 20
- Subsequent Starts 21
- 4.4 Front Panel Layout 22
- 5. Operator Level 2 24
- ☺ Press 27
- 5.4 Timer Operation 28
- 5.5 Dwell Timer 29
- 5.6 Delayed Timer 29
- 5.7 Soft Start Timer 30
- 5.8 Programmer 30
- 6.1.1 Level 3 33
- 6.1.2 Configuration Level 33
- 6.2 Parameter lists 35
- ☺ Press and hold 35
- 6.3 Navigation Diagram 36
- 6.4 Access Parameters 37
- 7. Controller Block Diagram 39
- Latching 41
- 9. Input/Output 43
- Note 1: 45
- 1. func 46
- 9.1.7 Output List 2 (OP-2) 47
- 9.1.8 Output List 3 (OP-3) 48
- Digital Input B 50
- 10. Setpoint Generator 52
- 11. Control 54
- 11.2.4 Manual Tuning 55
- 11.10 Control Parameters 57
- Deadband OFF 60
- Deadband ON 60
- 12. Alarms 61
- 12.1 Types of Alarm 62
- together 63
- 12.2.1 Example 1 64
- 12.2.2 Example 2 64
- 12.2.3 Example 3 64
- 12.3 Alarm Parameters 65
- 12.4 Diagnostic Alarms 67
- 13. Timer/Programmer 68
- 13.2 Programmer 70
- 13.2.3 Event Outputs 71
- Configure the Timer 74
- 15. Digital Communications 78
- RS232 80
- Address 81
- 15.4 DATA ENCODING 81
- 16. Calibration 92
- 16.2 Offsets 93
- 16.3 Input Calibration 95
- 0mV. Then: 96
- Ω and 400.00Ω 97
- 16.3.6 CT Calibration 100
- 16.4 Calibration Parameters 101
- 17.1.2 Configuration Clip 102
- 17.2 Starting iTools 103
- 17.3 Starting the Wizard 104
- 17.4 To configure the Input 105
- 17.5 To Configure Alarms 106
- 17.6 To Customise Messages 107
- 3100/3200 Series 108
- 17.7 To Promote Parameters 110
- 3100/3200 Series 111
- Press 112
- 17.9 To Set up Recipes 113
- 17.9.2.1 Recipe Definition 114
- 17.9.2.3 Recipe Names 115
- 17.10 Summary 116
- 17.11 Cloning 117
- 19. Parameter Index 120
- 20. Index 122
Related products and manuals for Processors Eurotherm 3116 PID
(71 pages)© 2020, manymanuals.com. All rights reserved. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals