Eurotherm 3116 PID User's Guide Page 32
- Page / 126
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
3100/3200 Series
30 Part No HA028651 Issue 3.0 Mar-06
5.8.3 To Configure the Programmer
Select Access Level 2 – see section 4.
Operation Action Indication Notes
Configure the
Timer as a
Programmer
1.
Press
to select ‘TM.CFG’
2. Press
▼
or
▲
to ‘ProG’
Set the
Resolution
3.
Press
to select ‘TM.RES’
4. Press
▼
or
▲
to ‘Hour or
‘min’’
In this example the ramp rate and dwell
period are set in hours
Set the
Threshold
5.
Press
to select ‘THRES’
6. Press
▼
or
▲
to adjust
In this example the dwell periods will not
start until the PV is within 5 units of the
setpoint
Set the action
when the
programmer
times out
7.
Press
to select ‘END.T’
8.
Press
▼
or
▲
to ‘Off’ or
‘
SP2‘ or ‘Dwel’ or ‘rst’
In this example the controller will
continue to control indefinitely at the last
setpoint.
OFF will turn the output power.
SP2 will control at setpoint 2
Reset will control at the selected setpoint
Set the Servo
Mode
9.
Press
to select ‘SERVO’
10.
Press
▼
or
▲
to ‘PV’, ‘SP‘,
‘
SP.rb’, or ‘PV.rb’
In this example the program will start
from the current value of the process
temperature. See also section 5.4.1.
Set the first
Target
Setpoint
11.
Press
to select ‘TSP.1’
12. Press
▼
or
▲
to adjust
In this example the setpoint will ramp
from the current value of the PV to the
first target - 100
Set the first
Ramp Rate
13.
Press
to select ‘RMP.1’
14. Press
▼
or
▲
to adjust
In this example the setpoint will ramp to
100 at 8.0 units per hour
Set the first
Dwell
15.
Press
to select ‘DWEL.1’
16. Press
▼
or
▲
to adjust
In this example the setpoint will remain at
the start value for 2 hours 11 minutes
Repeat the above three steps for all segments
Notes:-
• It is possible to set, in a deeper level of access, Event Outputs and Programmer Cycles. See sections 13.2.3 and 13.1.
• ‘Event Outputs’ is available in software version 2 and above. A digital event may be configured to operate in any segment of
the program. This event may be configured to operate a digital output.
• ‘Programmer Cycles’ is available from software versions 2.09 (PID controllers) and 2.29 (Valve Position controllers). This
allows the programmer to repeat the set program up to 100 times.
- 3100/3200 1
- 1.3 Dimensions 8
- 1.4 Step 1: Installation 9
- 1.5 Order Code 10
- 2. Step 2: Wiring 11
- 2.5 Wire Sizes 13
- 2.6 Precautions 13
- 2.13 Current Transformer 15
- Local ground 16
- Diagram 17
- ☺ Helpful hints 18
- Pollution Degree 2 19
- 4. Switch On 20
- Subsequent Starts 21
- 4.4 Front Panel Layout 22
- 5. Operator Level 2 24
- ☺ Press 27
- 5.4 Timer Operation 28
- 5.5 Dwell Timer 29
- 5.6 Delayed Timer 29
- 5.7 Soft Start Timer 30
- 5.8 Programmer 30
- 6.1.1 Level 3 33
- 6.1.2 Configuration Level 33
- 6.2 Parameter lists 35
- ☺ Press and hold 35
- 6.3 Navigation Diagram 36
- 6.4 Access Parameters 37
- 7. Controller Block Diagram 39
- Latching 41
- 9. Input/Output 43
- Note 1: 45
- 1. func 46
- 9.1.7 Output List 2 (OP-2) 47
- 9.1.8 Output List 3 (OP-3) 48
- Digital Input B 50
- 10. Setpoint Generator 52
- 11. Control 54
- 11.2.4 Manual Tuning 55
- 11.10 Control Parameters 57
- Deadband OFF 60
- Deadband ON 60
- 12. Alarms 61
- 12.1 Types of Alarm 62
- together 63
- 12.2.1 Example 1 64
- 12.2.2 Example 2 64
- 12.2.3 Example 3 64
- 12.3 Alarm Parameters 65
- 12.4 Diagnostic Alarms 67
- 13. Timer/Programmer 68
- 13.2 Programmer 70
- 13.2.3 Event Outputs 71
- Configure the Timer 74
- 15. Digital Communications 78
- RS232 80
- Address 81
- 15.4 DATA ENCODING 81
- 16. Calibration 92
- 16.2 Offsets 93
- 16.3 Input Calibration 95
- 0mV. Then: 96
- Ω and 400.00Ω 97
- 16.3.6 CT Calibration 100
- 16.4 Calibration Parameters 101
- 17.1.2 Configuration Clip 102
- 17.2 Starting iTools 103
- 17.3 Starting the Wizard 104
- 17.4 To configure the Input 105
- 17.5 To Configure Alarms 106
- 17.6 To Customise Messages 107
- 3100/3200 Series 108
- 17.7 To Promote Parameters 110
- 3100/3200 Series 111
- Press 112
- 17.9 To Set up Recipes 113
- 17.9.2.1 Recipe Definition 114
- 17.9.2.3 Recipe Names 115
- 17.10 Summary 116
- 17.11 Cloning 117
- 19. Parameter Index 120
- 20. Index 122
Related products and manuals for Processors Eurotherm 3116 PID
(71 pages)© 2020, manymanuals.com. All rights reserved. | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals