Eurotherm 3216i User Manual download pdf (Page 17)

3200iSeries Indicators

Part No HA029006 Issue 5.0 Sept-12 15

4. Switch On

4.1 New Indicator

If the indicator is new and has not previously been

configured, or following a ‘Cold Start’ (section 6.5), it

will start up showing the ‘Quick Configuration’ codes.

This is a built in tool which enables you to configure

the input type and range, the output functions and

the display format.

Incorrect configuration can result in damage

to the process and/or personal injury and must be

carried out by a competent person authorised to do

so. It is the responsibility of the person

commissioning the instrument to ensure the

configuration is correct

The quick code consists of two ‘SETS’

of five characters.

The upper section of the display shows the set

selected, the lower section shows the five digits

which make up the set.

Adjust these as follows:-.

1. Press any button

. The first character will change

to a flashing ‘-‘.

2. Press

to change the flashing character

to the required code shown in the quick code

tables –see next page. Note: An

x indicates

that the option is not fitted.

3. Press



to scroll to the next character.

☺ You cannot scroll to the next character until the

current character is configured.

☺ To return to the first character press



4. When all five characters have been configured

the display will change to rng.hi followed by

rng.lo which allows range high and low limits to

be set.

5. The next press of



will select Set 2. Adjust

each character as described for Set 1.

6. When the last character has been entered press



again, the display will show . Continue

to press



if you wish to repeat the above

quick codes or press

to if you

are satisfied with the quick codes. The indicator

will then automatically go to the operator level

SET 1

K C H C 0

Input Type

G Strain gauge

32h8i only

Thermocouple

B Type B

J Type J

K Type K

L Type L

N Type N

R Type R

S Type S

T Type T

C Custom C

RTD

P Pt100

Linear (all units)

M 0-80mV

2 0-20mA

4 4-20mA

Linear 32h8i

0 0-10Vdc

1 1-5Vdc

3 2-10Vdc

6 0-5Vdc

Display

units

Decimal point

Temperature

0 nnnnn

(1)

X None 1 nnnn.n

(1)

C 2 nnn.nn

(1)

F 3 nn.nnn

(1)

K K 4 n.nnnn

(1)

P %

32h8I only:

0 Pa D L-m

1 mPa E %RH

2 Kpa G %O2

3 Bar H %CO2

4 mBar J %CP

5 PSI L V

6 Kg/cm

M Amp

7 mmWG R mA

8 inWG T mV

9 mmHG U Ohm

A Torr W ppm

B L-H Y RPM

Z m-s

PV Colour

(2)

32h8i only

G Green

R Red

C Colour change on Alarm.

Green to red

X Not applicable

Set 2 follows these

parameters

See next page

(1) Up to 2 decimal places on 3216i and 3204i

Up to 4 decimal places on 32h8i

(2) Colour change on top part of display only

Set 1 is followed Set this for the maximum

with RNG.H I display range required

Then Set this for the minimum

RNG . Lo

display range required

Home display

N PV only

A First Alarm SP only

1 PV + Alarm SP

2 PV + Alarm SP

(Read only)

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 87 88

Comments to this Manuals

No comments

Eurotherm 3216i User Manual Page 17

Comments to this Manuals

Related products and manuals for Carbon monoxide (CO) detectors Eurotherm 3216i